PUBG Mobile Sensitivity on iPhone 13 — What Actually Works
The iPhone 13 has a 60Hz display, an A15 chip that handles frame pacing better than older hardware, and a touch sampling rate that responds quickly. Most players leave their sensitivity at factory defaults and wonder why their sprays drift upward or their recoil control feels sluggish. It isn't the phone. It's the calibration. There isn't a single code you paste that changes everything. PUBG Mobile doesn't work like that. Sensitivity settings are stored locally on your device and synced through your account. What you can do is load a set of calibrated values that match the iPhone 13's screen size, weight distribution, and touch response, then adjust from there over a few sessions. Here are the values I use on my iPhone 13 and recommend starting with:
Camera (Free Look): Gyroscope 400%, ADS Gyroscope 350% Camera (Non-Gyro): No Scope 120%, Red Dot 50%, 2x Scope 36%, 3x Scope 24%, 4x Scope 18%, 6x Scope 12%, 8x Scope 10% ADS (Recoil Control): Red Dot 55%, 2x 40%, 3x 30%, 4x 22%, 6x 14%, 8x 10%
Gyroscope: Camera 300%, Red Dot 300%, 2x 250%, 3x 200%, 4x 160%, 6x 100%, 8x 80% I started with those exact numbers after a tournament match where my 3x spray was pulling so hard right I couldn't keep a magazine on target past 40 meters. The issue wasn't my grip or my thumb speed. The default gyroscope settings on iPhone 13 run too low for controlled recoil absorption at medium range. These values brought my 3x ADS into a 15-meter control zone where I could track heads consistently. Load these values manually in Settings > Sensitivity. I don't use import codes because they're unreliable — most codes online haven't been updated since the last major sensitivity rebalance, which was in mid-2024. Even when they load correctly, the device-specific calibration makes them a starting point, not a finished setup.
Get the Full Details
The one edge case that trips people up: the gyroscope only activates when you're firing. If you tap the gyro button and it says disabled, check your control scheme. If you're on classic touch controls without gyro enabled, none of these numbers matter. Switch to gyro-assisted or full gyro mode before adjusting. After you apply the values, test them. Take the same 3x spray pattern you were failing at before — three consecutive mag dumps on a wall at 30 meters. If the recoil still climbs, drop the 3x ADS by 3 points and repeat. If it drops too fast and you can't track the target, add 2 back. This tuning process takes about 12 to 18 minutes on a fresh setup, and the change usually holds after the third session as your muscle memory locks in. There's a limitation worth acknowledging: these values assume you're playing at 60 frames per second with gyroscope on. If you're running smooth low frame rate or have gyro disabled, the camera and ADS numbers will feel disconnected. The gyroscope numbers are where the real difference lives on iPhone 13. Without gyro, you're relying entirely on thumb drag, which is fine for close-range engagements but inadequate for mid-to-long spray control.
Another thing beginners miss — the 6x scope value. Most players treat 6x as a sniper scope and forget it's also a viable DMR and short-spray setup when zoomed to 3x. Those 100% gyro and 14% ADS values for 6x make it usable for tapping and short bursts at 50 to 80 meters. I learned that the hard way after buying a M24 and wasting six matches trying to snipe with it at default sensitivity before realizing the scope itself wasn't the problem. If you want something closer to a shareable reference, search for the phrase I mentioned above. You'll find community posts that republish these kinds of optimized sensitivity setups for iPhone 13, sometimes with slight adjustments based on individual play style. The numbers will be within 5 to 10 points of what I listed, which is close enough to start from. The bottom line is simple enough to state without drama. Default sensitivity on iPhone 13 is designed for a general audience, not players who spray with 3x or 4x regularly. Adjusting these numbers takes an afternoon of testing, but once you've dialed them in, you won't need to think about it again. Return to default only if a game update changes the underlying physics, which happens maybe once a year, and even then the changes are minor enough that you can reset and retune in under 20 minutes.
